This routine pares down the clock setting routine to hopefully
a core minimum set of side-effects while allowing the system
to boot.
It also takes the register bank offsets as arguments, as well
as various functions to accomplish different tasks as argument,
so that it can be used in different contexts (such as in `std`).
Finally, the BIO clock rate can be set to slow or fast. The power
cost of the fast setting is about 12mW. If you're not needing
the high speed features of the BIO, slow setting is probably what
you want.
Currently, the system is configured such that after boot1, the
BIO is running in slow mode (to save power for battery powered
configurations); and then the clock set calls in baremetal and
dabao bump this up to the fast speed since these two configurations
are assumed to be running off of a USB wire with ample power.
Previous implementation sent the QR code as draw commands.
This is inefficient as it would require hundreds of draw
commands to be sent per QR code rendered.
This implementation codes the QR code as a bool and sends
it in a single memory message, and implements a QR code renderer
on the receiver side.
The QR code rendering is also cleaned up so that the QR code is
always centered and takes the full screen, to give the best
conditions for someone scanning the code from another device.
glitches can trigger interrupts from several sources:
- ECC errors on multiple blocks
- consistency check errors on hardened logic
- light sensor
- voltage sensor
- glue cells
These primitives respond to these glitches in an interrupt
context. At the moment, by default a fairly lax approach is
taken to responding to the glitches: partially, we want to make
sure that the sensors aren't too sensitive and trigger by accident.
The final thresholds can be adjusted fairly readily.
In addition, the mesh can trigger an interrupt, and typically,
that interrupt is a false reading (because the mesh takes a
long time to settle, and we boot the system while the mesh
settles). Thus, we take an approach of polling the mesh
effectively, and when interrupts happen due to the mesh we
just clear it and ignore it and allow the polling routine
to manage the mesh. The mesh is theorized to be a static
attack, anyways.
this is used by the key erase proof routine, but will be
useful in general for storing data in the buram
also, the ranges of slices are currently defined at
the top of the file but might be moved somewhere more
maintainable later.
RRAM writing got bollards added to it, as RRAM write could
be a glitch target: if a glitch could manipulate the
address somehow to stick stuff at an arbitrary location,
during write, that would be bad. However, it's probably
also reasonably dangerous to try and glitch RRAM writes
because there's a chance you spray over off-target items
and thus trigger a signature check failure on your next
boot.
A problem was discovered while implementing the secure boot
hardening. Namely, an attacker could trick the loader into
loading a devkey-signed kernel by incrementing the
developer mode counter without actually triggering the
secure erase of the keys, and finding a way to glitch
over the check of the developer mode counter check.
Two countermeasuers are implemented:
1. if the developer mode flag is set, trigger a secure erase
even if the image signatures aren't developer mode
2. leak one of the chaff keys into the loader, so there are
now at least two indpendent checks of being in developer
mode in the loader. One is based on the counter, which
is only weakly correlated with the erased state. The
other is checking for the erase value in the leaked key,
which is a strong indicator of being in developer mode.
The leaked key is, of course, erased before entering the
kernel (and the key is leaked into a region of memory
that is, in theory, securely claimed by the keystore, so
it's not like anyone can just read it; however, it is
in a less secure location than the protected key area).
The impact of an adversary obtaining the key is only
a slight weakening of security because the chaff keys
are numerous, they still have thousands of bits to
guess even if they got a couple hundred of them.
The next series of patches implements the scheme outlined
above, starting with defining the key to be leaked. The
leaked key is intentionally the last key in the slice
of keys used in the erasure algorithm, so that presumably
if the leaked key is showing an erased value, all other
keys have been erased.
this correctly gives the loader 256k of space, which is what
its link file specifies. The loader was previously under 128k
by chance, but with glitch hardening it's grown past that
boundary.
Signature checking parameters are now consolidated into
a single "SecurityConfiguration" record. This allows the
sum total of security state transitions to be summarized in
the bao1x-api/src/pubkeys/mod.rs file, easing maintenance
and audit.
Reaction to the signature check is split into a `hardened_erase_policy`
API call which can take the results of the signature check and
react to it if necessary.
This allows the signature check routine to be used for both
audit (where reaction is not necessary) and for live testing
of the code (where reaction is required). It also simplifies
the implementation of double-checking signatures in the case
of paranoid mode.
Another important improvement is that the signature checking
API outputs the target address for the jump, but masked with
an XOR of the function code of the signed block. The purpose
of the XOR mask isn't to obfuscate the value; rather, it's
to prevent there being a single, simple, fixed-constant
jump instruction laying around that a glitcher can use as
a target: instead, a pair of registers must be loaded
with the target and its mask. This is an example of what
the final jump looks like:
```
60003a8e: ffffffff .word 0xffffffff
60003a92: 0440006f j 60003ad6 <bao1x_hal::hardening::die>
60003a96: ffffffff .word 0xffffffff
60003a9a: 167d addi a2,a2,-1
60003a9c: fe71 bnez a2,60003a78 <rust_entry+0x2f74>
60003a9e: a00d j 60003ac0 <rust_entry+0x2fbc>
60003aa0: 0360006f j 60003ad6 <bao1x_hal::hardening::die>
60003aa4: ffffffff .word 0xffffffff
60003aa8: 02e0006f j 60003ad6 <bao1x_hal::hardening::die>
60003aac: ffffffff .word 0xffffffff
60003ab0: 0260006f j 60003ad6 <bao1x_hal::hardening::die>
60003ab4: ffffffff .word 0xffffffff
60003ab8: 01e0006f j 60003ad6 <bao1x_hal::hardening::die>
60003abc: ffffffff .word 0xffffffff
60003ac0: 0149c533 xor a0,s3,s4
60003ac4: 600805b7 lui a1,0x60080
60003ac8: d0058593 addi a1,a1,-768 # 6007fd00 <_etext+0x6e9dc>
60003acc: 82aa mv t0,a0
60003ace: 852e mv a0,a1
60003ad0: 4581 li a1,0
60003ad2: 8282 jr t0
```
So here you can see the alternating bollards in the region that
will cause any glitches that don't land exactly right to
either halt the machine or cause a reaction.
Line 0x6003ac0 is where the xor happens to compute the target
address. Should a glitcher land on that address, `s3` and `s4`
will need to be loaded with the target address and a value when
XOR'd with it that yields a meaningful result. While there is
a non-zero chance that this can be arranged, it's definitely
not as easy as targeting a jump-to-fixed address exit sequence.
The management of different security configurations was getting
a bit out of hand, so all the security configurations used by
the system and their transitions are now consolidated into a single
file, This will make auditing and checking the transitions a lot
easier.
This allocates some additional one way counters dedicated
to hardening:
- Paranoid mode is duplicated in slots 65 & 67
- An attack counter is in slot 66
- Redundant revocation counters are seated in slot 68
The primary revocation counters are in slot 116. This means
that cutting out the revocation counters would probably require
at least two edits to the memory array - simply cutting the
word addressing line for those columns might be enough to
defeat a counter.
Paranoid mode duplicate is stored somewhat close to the
primary counter, which means it could be subject to a single
line cut to fully defeat the counter, but the space is getting
pretty crowded so I'll leave it like that; I really want to
leave the bottom 64 slots available for application use.
A "flag" key is allocated, plus a dummy flag is committed
to the repo. This is a value that, if retrieved, would
ostensibly bring the retriever glory and bounty, to the
extent that any glory or bounty is to be had (ps: I'm poor
and this project is obscure). The actual flag, of course,
is not in the repo...I hope!
The flag value is different from all other values in that
this is the only shared, common secret across all devices.
All other device secrets are generated on a per-device
basis from the TRNGs. So the flag needs some special treatment
such that it's not overwritten during device keying.
The flag exists because I'm hoping that anyone who manages
to extract it will also provide a helpful explanation of
the procedure to get it out, so that the system could be
patched (if the error is patchable) or rev'd in future
silicon. That being said, a flag retrieval is not necessarily
equal to a full break of security across all devices because
as mentioned above, most device secrets are on a per-device
basis. The flag represents then, the amount of effort necessary
to apply to every device to retrieve the secrets within.
clock setting calls, for legacy reasons, are duplicated in all the
stages of the bootloaders. This is a start toward moving these routines
into a common set of calls that improves maintainability.
These macros are added to the platform-agnostic API crate.
bollard is a macro that can respond to the following argument
formats:
bollard!(): inserts 4 illegal instructions and a jump over them
bollard!(#): inserts # of illegal instructions and a jump over them
bollard!(f, #): inserts # of an interleave of illegal instructions
and a jump to f
the last form is intended to "up the ante" by including a call
to a routine that can shut down the chip and/or wipe secrets
should the defender choose to do that. The other ones just
trampoline into an illegal instruction vector which is a fairly
weak defense because the CPU could once again get glitched out
of that.
HardenedBool is a boolean represented by a high-hamming distance
numeric value so that single-bit flips just lead to an invalid
bool, instead of a change in the meaning of the bool.
- key revocation check is fully duplicated and tested twice
- bollards & random delays added throughout the code. Random
delays require passing in a csprng object from the calling
environment.
- the primary go/no-go decision on whether a signature passes
or not is unfortunately not hardenable because the API is in
a third party crate. However, the regions around that call are
random-delayed and surrounded with bollards
- the state bits that determine whether the system is secure
and/or in developer mode are implemented using HardenedBool
- erase_secrets has some delays added to it as well as bollards.
However, it does remain a weakness that an attacker
could pull RRAM power during the erase cycle by just isolating
the RRAM power supply and putting a fast current limit on it,
thus preventing effective erasure by starving the circuit
of power.
Nothing we can really do about an active attack on the power
supply to prevent erasure, I think. It is unfortunately required
by design to have an isolated power supply for the RRAM to perform
elevated-voltage forming at CP time, and so, it should always
be possible to limit the current going into it thus preventing,
at least somewhat, any programming operations on the array.
One way counters are used ot record some security-critical properties,
such as key revocations and paranoid mode.
Two methods of retrieving the counters so that they are hardened
are provide here. Both of them rely on the fact that any value
other than 0 for the counter means it is set.
`hardened_get()` retrieves the counter value and sums it several
times. It does this *twice*, and returns *both* values as a tuple.
By returning both values as a tuple, it reduces the likelihood
that the compiler optimizes out the redundant read. The receiver
should implement serial checks that operate on the hardened_get()
result (i.e., test one value of the tuple, then test the other
value of the tuple redundantly, instead of OR'ing them together
into a single test)
`hardened_get2()` is for counters that are fully duplicated in
the array. For extremely critical counters, they are stored in
two physically separate elements. This is done to make bypass
of the counter harder than just FIB'ing out a single bit in
the memory array. In the case of `hardened_get2()`, a tuple
is returned, but instead of reading the same value twice, the
tuple corresponds to the summed value over each of the redundant
counters.
This library contains the following primitives:
check_pll() - checks that the PLL is the primary clock source.
This is important because allowing direct clocking of the system
from the external clock pin makes glitching much, much easier.
die() - a routine that implements a reaction to attacks. At the
moment, we just note attacks and then halt the machine. Eventually,
this could be upgraded to be more reactive, e.g. erasing secrets
or bricking the chip.
Csprng - this is a chacha8 cipher seeded with ring oscillator
TRNG data, plus whatever tiny bit of entropy we can scavenge
from uninitialized RAM (to make it so that it's not as trivial
as cutting the RO wire and tying it to 0 to bypass the library).
There's also a tiny health check on the RO before using it, again,
to make it harder than just cutting the RO wire. The sole purpose
of the Csprng is to generate random delays that frustrate glitching
attacks. The delay is currently tuned to a range of 0-255 iterations
of a loop.
paranoid_mode() - turns on fully automatic reactive sensor
countermeasures. Whenever a voltage glitch is detected, the system
will just reboot.
mesh countermeasures - these set up the secure mesh and the
reaction policy to tamper detection on the secure meshes
apply_attack_policy() - an API call that applies the currently
determined countermeasure in case that the detected attacks
counter has gone above a threshold. The reason we don't simply
react right away is that some countermeasures are fairly
sensitive, and *also*, very importantly, the chip *is* packaged
in a CSP and thus especially for dabao users you will expect
to see random trips of the attack sensors due to environmental
noise (photoflashes, nearby lightning strikes, etc.).
the video layer is the "traffic cop" managing when modals
get focus. This patch creates a feed from the video layer
that listers to subscribe to that filters out key presses
destined for modals.
Rust 1.91 (or perhaps, more accurately llvm?) changed how link
ordering works.
Previously, modules would be linked in the order they were referenced
(e.g. pub mod b; pub mod a; would result in b being at a lower address
than a in the resulting binary).
However, apparently, this has changed and now someone in their
infinite wisdom decided that modules should be alphabetized before
linking.
I'm really not sure why the arbitrary ordering of the human alphabet
is superior to any other system, and also, if you really wanted
things alphabetized, you could just alphabetize them in your
reference order.
Previously the fonts were laid out in a way that tried to minimize
cache thrashing by co-locating certain sets of fonts together.
Now they are just sprayed around through the arbitrary and not
terribly useful permutation funtion of the english alphabet.
Rant off.
This changes the specification of the fonts in the code generator
to be in alphabetical order, making the screen once again legible.
The -A1 stepping is going to tie the IFR access control
bits for data and key slots together. This is due to an RTL
bug where the key slot maps were typo'd and they ended
up mapping to the same IFR ACL.
We "could" continue to use key slots with a rule that
key and data slots would have to coordinate with each
other and not use the same slot number.
However, because of this linkage, and because there are
other bugs suspected in the keyslot implementation, an
executive decision was made to disregard the key slot
feature in the chip.
The main downsides of this are:
- fewer slots (2048 vs 4096)
- no key access linkage to HMAC auth on SCE
I *think* that's it.
Fewer slots - 2048 slots is still a lot of slots, about half are
used now, I think this is plenty.
Key access linkage to HMAC auth on SCE - I have reasons to
suspect this feature is broken anyways for subtle reasons
related to malleability of the HMAC round constants. Even
without that brokenness, it's hard to use HMAC auth to manage
the system because it requires per-device unique keys: so,
we're using a PKI scheme and no symmetric secrets to handle
access controls.
Removing the key slots also greatly simplifies the code
base analytically. This culling removes the key slot
abstraction the "simple" way, but without the weirdness
of the keyslots (in particular the key ID chaining which
makes them different from data slots) I could remove even
more abstractions and simplify the code.
One upside is now all elements can enjoy the write mode
behavior which can force the slot to be only 0->1 writeable,
which could be useful for other things down the road.
This was tested to not interfere with Dabao-Alpha 0
bootloaders.
this allows the OS to initialize the keys
note that including write access only gives it to the fw0 user,
which is the OS's secure user. thus any write primitive created
by this expansion of access should transitively also be a read
primitive (which is actually what the adversary desires).
In exchange the OS is allowed to initialize the keys, which
I think is the right place to do it given that it's too hard
at this point to nail down the exact key layout, etc.
Note that it is impossible for the OS to change ACLs - that is
a feature that can only be updated by the boot user - which
is why the boot user can change the ACL to gain access to
erase keys, but the OS user can't modify its own ACL.
make it long enough that it's unlikely to have two identical
ones randomly connected to the same machine
but short enough that it's likely/conceivable to have a collision
there is a lock that happens in serial console interactions with
local echo where the instant feedback of a character entered causes
the USB object to be locked when the interrupt handler enters to
receive a character that was just sent.
The fix to this is to add the ability to disable interrupts before
entering a critical section (such as enqueuing data for a write)
and then re-enabling after tha section is done.
After some contemplation, we should include the keystore in the
core service set featured by the dabao-xous configuration.
The pros are: any compatibility/sharing of resources
that require access to RRAM, one-way counters, UUIDs, etc.
will either require a wholly separate implementation that is
"insecure" or it could just reuse the baosec work. Furthermore,
as cryptographic accelerators are laid into the keystore,
the APIs become available to the dabao environment
The cons are: more space is used in a space-constrained
dabao environment (roughly 140k "deadweight" at the start, but
as cryptographic APIs get layered in this can grow substantially);
the key slots are "used up" in part by the scheme, which leaves
less key slots available for user-defined purposes.
This is mitigated by the fact that there are a couple thousand
key slots, and so even though we use a couple hundred of them
it's still not the whole range.
Also, the baosec/dabao feature flag can be used to feature-out
cryptographic APIs/accelerators that are too obscure or not
useful for the dabao environment, to "lighten up" the
firmware load.
identify_flash_reset_qpi's behavior has been revised to
include setting all relevant parameters so that the device
that is identified behaves identically to the model device
(e.g. Macronix), to the extent that it is possible. This
includes setting the QE bit.
The routine to check QE has been renamed to `flash_ensure_eq()`
to reflect that it is safe to call multiple times: it checks
if the bit is already set, and if so, doesn't do anything.
Thus it can be routinely called without worry of wearing
out the device.
xtx devices still not fully working, but at least able to switch
in and out of spim modes in the face of uncertainty over which
device type is present.
also fixup a return-type bug in the std implementation for
bio pin settings
much more bio abstractions will be needed, but for now,
this branch is just focused on the keystore.
just learned of another ECO incoming that will tie the key
and data areas together in terms of access control from
the IFR region, so the nuisance key range has to have
its access control redefined to steer clear of the data
slots allocated that have write-protects on them.
pubkey block is added to the data ranges
also a oneway counter to keep track of pubkey validation
failures in boot0 is added
The motivation for this is to make the tester configuration
exactly identical to that used in production. Right now a
"cheater" step is used to set the board type to dabao and
enable boot waiting because in the test environment there
isn't a physical switch anyone can press to invoke that
behavior.
So, in order to get the test environment to work just like
production, the behavior goes from insta-die if no valid
image is found on the next stage, to "wait for new image".
This is slightly less secure of a default, but only slightly
so. Basically the previous scheme required someone to be
physically present to press the "give me a new image" button,
this one causes the system to automatically accept a new image.
I suppose the main downside is this does allow the possibility
of say, a fully remote, automated exploit to be delivered
if an adversary can damage the loader image such that it
doesn't pass signature check and then it will automatically
go into a mode looking for a new image, at which point
an arbitrary image could be potentially loaded (although
because the image would need to be signed, and there is
a trap that destroys secrets if a developer image is
presented, it wouldn't instantly lead to secret disclosure,
but it would be a denial of service).
The flip side is that with the paranoid default, developers
are "confused" by the silent failure of a brand new chip that
has no code loaded in it (because it goes catatonic until
the developer knows to press the load button).
The loader image is protected from writes after boot, so
in theory there isn't a direct path to "spoil" the loader
image and trigger this path, so it's not like we're just
hanging in the wind. It just means that there isn't a
full human-presence requirement as a defense in depth against
a potential denial of service if an adversary could find
a way to spoil the loader image.
If the DoS path is a concern, one option is to configure
the system such that the developer key is revoked. This
would disallow that from being recognized as a valid
image, and would also prevent the DoS from happening,
as it would require the adversary to present a valid,
signed image which presumably they can't as long as
the signing keys are kept safe.
rram handler for `std` requires the following additional features
over baremetal:
- mapped pages list, because a process has to "own" a page of RRAM
before writing to it. It's anticipated that the rram writer hardware is
"owned" by the keystore, so all write-access will be mediated by a
service in that PID
- irq-context handling of writes. this prevents writes from being
detached from their staging data, or other concurrent writes
from conflicting.
the more i test things the less confidence i have.
this fixes up a missing table entry in the table definition,
and then also adds a bypass routine - this is not actually
a hidden vulnerability, it's an explicit vulnerability until
the protect() routine is called. But it looks like we may have
to exploit it in order to transform our userstate in
the bootloader to one that has write-access to keys in order
to erase them in case of a developer boot.
only some keys are marked as writeable to harden against
potential oracle attacks, i.e., if we made all keys
erasable and an oracle attack was found, then the entire
key region can be exposed by the oracle attack.
Instead, some key material always persists, but a sufficiently
large amount of seed material is erased such that the key is not
recoverable by guessing the key.
the key setup seems to work correctly
but the data ACL setting doesn't "stick". The region
could be write-protected by some other element in the
CP/IFR config, need to dig a lot more. For now we need
to move on and crank out something to stick on the alpha
dabao boards...
add read/write specs as well to the slot definitions.
Not terribly happy with how this all worked out. The subtle
differences between Data and Keys is really irritating.
it's the sort of thing you would say "let's make a trait"
for it but then the two behave just differently enough
that I worry I can't make a trait generic enough to encompass
all the weird stuff that exists in the hardware.
The existing implementation definitely looks like trait
territory, but it currently hides the subtleties around
key/data chaining and secure crypto engine handling of
the two regions as distinct entities. so long as we don't
plan to use those things, traits are a good idea, but
i don't feel like I can reject using the crypto engine
features out of hand this early on just to make the
APIs nice and square.
'coreuser' is a slightly confusing term from the hardware
system because it's overloaded to mean some conceptually
related items that aren't implementation-wise essentially linked.
coreuser defines both some access protections on the main
array of the RRAM, and also some access protections on key
and data slots.
this patch includes some code that sets up the coreuser
functionality to a very simple scheme where just one PID
is trusted and the rest are not trusted. More complicated
schemes could be introduced with varying levels of trust
and dependencies but I like the analytical simplicity of
two states, so let's start there and complicate only when
absolutely necessary.
Data and key slots are hardware access-controlled areas that
can store sensitive data. Slot definitions come with a "spec"
field that defines what the access controls *should* be,
so that we can check them later.
In practice no user code should be manipulating these, but
there is an initial stage where a totally blank device needs
to be provisioned, hence the focus on correct specification
and checking of state, rather than convenient runtime manipulation
and update of the same.
on dabao targets the duart is unavailable, so, it's convenient to
have a uart-based debug option in the HAL. this patch creates a
flag that can allow either target.
- add range checking to control access to main array or secure
array. This is purely a software enforced check, but it is in
theory backed by hardware gating that is a back stop in case
an adversary can gain arbitrary code access
- rework the rram primitive to return an error type
- add a `std` implementation stub. It is still missing an IRQ
context handler which ensures that all RRAM writes are atomic,
e.g. you can't take an interrupt in the middle of an RRAM
write because it would screw up the buffer staging.
auth_data actually changes with each signing operation (ostensibly
to prevent replay of signatures coming from tokens) so it has
to be presented as data parallel to the signature, instead of
as a static filed baked into the key header.
This commit revises the header record to reflect this organizatio
of data and also revises the signature check to be in-line
with the protocol.
have to absorb a version change due to xous-semver change
might as well also update the utra/svd generator dependencies
since that's been held off for a long time now.
this is the agnostic version of all of the board targets, which
allows the boot1 to lookup based on the current configuration
which configurations to apply.
I think I've talked myself into giving away $0.20 of parts with
every dabao board so that everyone can run at full frequency.
Originally I thought I'd limit to the minimal configuration with
low frequency operation but since this is the main developer
platform all the benchmarks and first impressions will come
through this board. Crippling it with a slower clock frequency
by omitting the supplementary digital regulator seems
short-sighted, even if it means up slightly subsidizing things
with this extra cost.
this cleans up one unsafe step where we have to assume an
alignment of the data at the cost of the structure being copied
to stack. I think this is a fine trade-off.
this implements the API/HAL split on the HAL side, and also
reveals SPIM channel as a constant that can be just read out
so that spim accessors that need to build from raw parts
can do it without having to re-allocate IOs.
In the API layer, the boards aren't setup with convenience flags.
they are all laid out and the caller needs to know which board
it's trying to resolve. This is because the API layer is agnostic
to board and assumes the tool working with it knows what board
it's working with already.
The HAL layer tries to hide the board-specific stuff, and so
API defines are re-imported there in a board-transparent fashion.
Also add swap descriptors to the API crate, so that the image
generation tools can refer to the exact same structures as
are used inside the code, simplifying image creation maintenance.
this puts a domain separator in every signature block
a domain separator meaning, even though the same private key
maybe be used to sign multiple blocks, because a functional code
is embedded in the block that is tied to the block's function, you
can't take a pre-signed block and shove it into another block's slot
and expect it to work.
the top of memory is reserved for various security structures
the security structures do have some hardware protection
but life is better when we also help programmers avoid triggering
the protections by accident and then just being confused.
just pulled it out of a uuid generator, checked it has no
collisions. At some point, maybe some official repo will allow
us to be "real" but ain't nobody got time for those politics
today.
- combohash constants are moved to API: these need to be in a
dependency-free library so that we can refer to these values in
any context without creating circular dependencies
- sigcheck code is now put into the HAL layer, instead of in the
individual bootloaders. This is because the sigcheck code is re-usable
between boot0/boot1.
- sram timing trimming data has been entered from the XLS file
and put into an array for easy access
- more board initialization functions have been adedd, and cleaned
up to adhere to the rule that pin allocations don't change the state
of the pins, allowing pin allocation calls to be idemptoent (e.g.
you can call it several times without negative effects - the reason
being that the pin setups also return the pin maps, which can then
be passed to the functions of interest to manipulate the pin states)
A macro is added, a bit like this one:
```
encode_oneway! {
#[offset = 80]
pub enum BootWaitCoding {
Disable,
Enable,
}
}
```
Which encodes possible one-way counter states along with their
offset in the one-way counter array.
The states in the enum correspond to the evolution of the counter,
modulo the number of elements in the enume.
The macro also creates a getter for the states, and an incrementer
to try and make this whole process less error-prone.
By adding a resolver to a given glyph set, the glyph set is
automatically pulled into the image.
Glyph set is now co-located in the bao-video process, instead
of the loader.
The orignial argument for putting the font data in the loader
is that it's a large, static blob; by putting it in the loader,
updates can be more compact, and fonts don't need to be schlepped
over every time you have an application update.
This came with consequences. It made verifying the loader more
complicated (because its memory space is split between the graphics
manager and root keys). It also means we have to fix the partition
size for the loader at "fairly large" for fonts, even if we don't
need all of them in all of the configs.
With baochip, we have swap memory! Off-chip memory is cheap and
only the fonts actually used by the host get mapped into main memory.
This means we don't have as much of a trade-off in terms of
cost for fonts if we put them in off-chip swap storage. Also,
the updates are split between swap and main memory, and the roadmap
includes an item for swap to be individually loadable programs
so that if the video server doesn't need an update, it won't be
pulled into the update set.
a small, 256-byte record is added to the top of baremetal records
that is a "poke table" that incorporates what values to put where
for baremetal targets, as well as a zeroization region.
This is generally more efficient because most values are set to
zero, and the only things that generally have a non-zero value
are 'static' variables, which are used extremely sparingly.
The code base had evolved through several code names, interim
names, company names and chip names that alternatively did or did
not exist.
Baochip is the definitive name of the company, and the Baochip1x
(full part number BAO1X2S4F-WA) is the definitivey part number of
the SoC. For convenience, the part number is shortened to 'bao1x'
in most feature flags and variable references.
This commit fixes all of the odd names and removes some unmaintained
early targets.
usb-device has a limitation for this hardware in that it can't
initiate an ep0-receive. It has a hook for flipping ep0 from
IN to OUT (as a modal thing) but for our stack you need to
explicitly setup EP0 to receive - an exact amount of data based
on what's expected - exactly at the point of the setup packet
arriving saying an OUT transaction is pending.
The hack to work-around this is to simply intercept those setup
packets in the handle_event_inner() interrupt handler and initiate
the receive. In fact, the data is completely ignored (in our
application it's setting a baud rate which is fictional in our
system). However, clients such as windows will time out and
refuse to communicate if the OUT packet is not ACK'd, even if
it is ignored.
- endpoint allocator now handles more edge cases. likely there
are still more weird cases to be considered, but it at least
handles the CDC-ACM case of a lone interrupt endpoint that
can't be mix-and-matched with other devices
- initiate OUT to kick off reads
- remove dead code
- handle bulk and interrupt cases for both read and write
- clean up reset edge cases - still more work to do there,
the stack does not recover on second plugin
- better debug output
previously we had no way to correlate an incoming packet
to an actual read from the USB stack because we didn't store
the EP that originated the request
This fixes that issue and also passes on the pending EP requests
correctly to the rest of the stack
there is either a code bug or a compiler issue that is causing
something on stack to be smashed that is causing trouble for
the code base as a whole. Or it could be improperly initialized
statics? unclear. this needs to be worked through.
however, a series of changes were made that make the code
work. The biggest tell is that the code generally works perfectly
when optimizations are off, but when optimizations are on some
shenanigans have to happen to convince the compiler to not split
constant values across the entire arc of the function. More
diagnostics to follow.
NACK bit is now checked after running the transaction, and if
it is set an appropriate error code is returned.
The trait implementation for i2c baremetal calls is also
updated in this commit
in the Xous context, because the IRQ banks are owned by a global
object, not every server can simply refer to the IRQ bits by just
dereferencing a pointer. Instead, it needs to send a message to
the cram_hal_service with an API number which then catches this
and does the dereference on behalf of the caller.
multiple IRQs related to the UDMA will eventually get mapped into
the global IRQ handler for UDMA. Create an enum type that will
help us differentiate this and add a trait that returns the raw bits
for a given IRQ type.
Probably a fancier wrapper should be made to interptet the IRQ
bits but unfortunately there isn't a uniform pattern to the IRQ
mappings, it's pretty much whatever fit into the IRQ space based
on the underlying function. At the moment not even sure if this
is the right register to be chasing, so we'll use this for probing
that aspect and then get fancy later, maybe.
the switch based on target is now absorbed into the new() function.
This paves the way for us to add more CSR ranges into the global
configuration object, i.e. IRQ csrs for I2C.
our implementantation of Buffer can't (currently) dynamically grow
the size of the object to serialize things that are bigger than
a page, so we have to enforce Vec-like objects to have a serialized
size of less than the page limit.
This is a bit of a moving target because it depends on implementation
specific details. A conservative bodge was put in to try and
work around this problem for now.
This was introducing a mysterious "line" artifact on text rendering
in new systems.
Probably need to do some real on-device testing of this change
because the automated tests won't catch a dirty bit error on
the LCD.
cramium-soc i think should be deprecated everywhere because
it is redundant with the board targets: anywhere you see a board
target that includes the crossbar soc it should also transitively
pull in the cramium-soc dependency equivalents.
we'll chase this out more later, but for now we're just trying
to get the PDDB to compile
This is a bad idea because yield_slice() causes the active
process to hand off to a new one (without an IRQ). However,
the idea of most flash operations is we really want them
atomic - we can't have something else decide to go and muck
with flash while say, we are waiting for a page erase to
complete. So, implement spin locking to block the CPU
during phases where the hardware operation is non-interruptable.
BOOKEND test sentinels are moved out of xous-rs, and into the
board definitions allowing us more flexibility on configuration
board-specific test configs (before it was a xous-wide constant,
which seems a bad idea because it makes migrating test infra
hard as the manufacturing infra updates)
MMAP_VIRT as a range is also added is this commit
this allows us move board-specific parameters out of xous-rs
and into a board library that is consistent with the new board
libraries, reducing special case code for Precursor