This routine pares down the clock setting routine to hopefully
a core minimum set of side-effects while allowing the system
to boot.
It also takes the register bank offsets as arguments, as well
as various functions to accomplish different tasks as argument,
so that it can be used in different contexts (such as in `std`).
Finally, the BIO clock rate can be set to slow or fast. The power
cost of the fast setting is about 12mW. If you're not needing
the high speed features of the BIO, slow setting is probably what
you want.
Currently, the system is configured such that after boot1, the
BIO is running in slow mode (to save power for battery powered
configurations); and then the clock set calls in baremetal and
dabao bump this up to the fast speed since these two configurations
are assumed to be running off of a USB wire with ample power.
glitches can trigger interrupts from several sources:
- ECC errors on multiple blocks
- consistency check errors on hardened logic
- light sensor
- voltage sensor
- glue cells
These primitives respond to these glitches in an interrupt
context. At the moment, by default a fairly lax approach is
taken to responding to the glitches: partially, we want to make
sure that the sensors aren't too sensitive and trigger by accident.
The final thresholds can be adjusted fairly readily.
In addition, the mesh can trigger an interrupt, and typically,
that interrupt is a false reading (because the mesh takes a
long time to settle, and we boot the system while the mesh
settles). Thus, we take an approach of polling the mesh
effectively, and when interrupts happen due to the mesh we
just clear it and ignore it and allow the polling routine
to manage the mesh. The mesh is theorized to be a static
attack, anyways.
this is used by the key erase proof routine, but will be
useful in general for storing data in the buram
also, the ranges of slices are currently defined at
the top of the file but might be moved somewhere more
maintainable later.
RRAM writing got bollards added to it, as RRAM write could
be a glitch target: if a glitch could manipulate the
address somehow to stick stuff at an arbitrary location,
during write, that would be bad. However, it's probably
also reasonably dangerous to try and glitch RRAM writes
because there's a chance you spray over off-target items
and thus trigger a signature check failure on your next
boot.
Signature checking parameters are now consolidated into
a single "SecurityConfiguration" record. This allows the
sum total of security state transitions to be summarized in
the bao1x-api/src/pubkeys/mod.rs file, easing maintenance
and audit.
Reaction to the signature check is split into a `hardened_erase_policy`
API call which can take the results of the signature check and
react to it if necessary.
This allows the signature check routine to be used for both
audit (where reaction is not necessary) and for live testing
of the code (where reaction is required). It also simplifies
the implementation of double-checking signatures in the case
of paranoid mode.
Another important improvement is that the signature checking
API outputs the target address for the jump, but masked with
an XOR of the function code of the signed block. The purpose
of the XOR mask isn't to obfuscate the value; rather, it's
to prevent there being a single, simple, fixed-constant
jump instruction laying around that a glitcher can use as
a target: instead, a pair of registers must be loaded
with the target and its mask. This is an example of what
the final jump looks like:
```
60003a8e: ffffffff .word 0xffffffff
60003a92: 0440006f j 60003ad6 <bao1x_hal::hardening::die>
60003a96: ffffffff .word 0xffffffff
60003a9a: 167d addi a2,a2,-1
60003a9c: fe71 bnez a2,60003a78 <rust_entry+0x2f74>
60003a9e: a00d j 60003ac0 <rust_entry+0x2fbc>
60003aa0: 0360006f j 60003ad6 <bao1x_hal::hardening::die>
60003aa4: ffffffff .word 0xffffffff
60003aa8: 02e0006f j 60003ad6 <bao1x_hal::hardening::die>
60003aac: ffffffff .word 0xffffffff
60003ab0: 0260006f j 60003ad6 <bao1x_hal::hardening::die>
60003ab4: ffffffff .word 0xffffffff
60003ab8: 01e0006f j 60003ad6 <bao1x_hal::hardening::die>
60003abc: ffffffff .word 0xffffffff
60003ac0: 0149c533 xor a0,s3,s4
60003ac4: 600805b7 lui a1,0x60080
60003ac8: d0058593 addi a1,a1,-768 # 6007fd00 <_etext+0x6e9dc>
60003acc: 82aa mv t0,a0
60003ace: 852e mv a0,a1
60003ad0: 4581 li a1,0
60003ad2: 8282 jr t0
```
So here you can see the alternating bollards in the region that
will cause any glitches that don't land exactly right to
either halt the machine or cause a reaction.
Line 0x6003ac0 is where the xor happens to compute the target
address. Should a glitcher land on that address, `s3` and `s4`
will need to be loaded with the target address and a value when
XOR'd with it that yields a meaningful result. While there is
a non-zero chance that this can be arranged, it's definitely
not as easy as targeting a jump-to-fixed address exit sequence.
- key revocation check is fully duplicated and tested twice
- bollards & random delays added throughout the code. Random
delays require passing in a csprng object from the calling
environment.
- the primary go/no-go decision on whether a signature passes
or not is unfortunately not hardenable because the API is in
a third party crate. However, the regions around that call are
random-delayed and surrounded with bollards
- the state bits that determine whether the system is secure
and/or in developer mode are implemented using HardenedBool
- erase_secrets has some delays added to it as well as bollards.
However, it does remain a weakness that an attacker
could pull RRAM power during the erase cycle by just isolating
the RRAM power supply and putting a fast current limit on it,
thus preventing effective erasure by starving the circuit
of power.
Nothing we can really do about an active attack on the power
supply to prevent erasure, I think. It is unfortunately required
by design to have an isolated power supply for the RRAM to perform
elevated-voltage forming at CP time, and so, it should always
be possible to limit the current going into it thus preventing,
at least somewhat, any programming operations on the array.
One way counters are used ot record some security-critical properties,
such as key revocations and paranoid mode.
Two methods of retrieving the counters so that they are hardened
are provide here. Both of them rely on the fact that any value
other than 0 for the counter means it is set.
`hardened_get()` retrieves the counter value and sums it several
times. It does this *twice*, and returns *both* values as a tuple.
By returning both values as a tuple, it reduces the likelihood
that the compiler optimizes out the redundant read. The receiver
should implement serial checks that operate on the hardened_get()
result (i.e., test one value of the tuple, then test the other
value of the tuple redundantly, instead of OR'ing them together
into a single test)
`hardened_get2()` is for counters that are fully duplicated in
the array. For extremely critical counters, they are stored in
two physically separate elements. This is done to make bypass
of the counter harder than just FIB'ing out a single bit in
the memory array. In the case of `hardened_get2()`, a tuple
is returned, but instead of reading the same value twice, the
tuple corresponds to the summed value over each of the redundant
counters.
This library contains the following primitives:
check_pll() - checks that the PLL is the primary clock source.
This is important because allowing direct clocking of the system
from the external clock pin makes glitching much, much easier.
die() - a routine that implements a reaction to attacks. At the
moment, we just note attacks and then halt the machine. Eventually,
this could be upgraded to be more reactive, e.g. erasing secrets
or bricking the chip.
Csprng - this is a chacha8 cipher seeded with ring oscillator
TRNG data, plus whatever tiny bit of entropy we can scavenge
from uninitialized RAM (to make it so that it's not as trivial
as cutting the RO wire and tying it to 0 to bypass the library).
There's also a tiny health check on the RO before using it, again,
to make it harder than just cutting the RO wire. The sole purpose
of the Csprng is to generate random delays that frustrate glitching
attacks. The delay is currently tuned to a range of 0-255 iterations
of a loop.
paranoid_mode() - turns on fully automatic reactive sensor
countermeasures. Whenever a voltage glitch is detected, the system
will just reboot.
mesh countermeasures - these set up the secure mesh and the
reaction policy to tamper detection on the secure meshes
apply_attack_policy() - an API call that applies the currently
determined countermeasure in case that the detected attacks
counter has gone above a threshold. The reason we don't simply
react right away is that some countermeasures are fairly
sensitive, and *also*, very importantly, the chip *is* packaged
in a CSP and thus especially for dabao users you will expect
to see random trips of the attack sensors due to environmental
noise (photoflashes, nearby lightning strikes, etc.).
The -A1 stepping is going to tie the IFR access control
bits for data and key slots together. This is due to an RTL
bug where the key slot maps were typo'd and they ended
up mapping to the same IFR ACL.
We "could" continue to use key slots with a rule that
key and data slots would have to coordinate with each
other and not use the same slot number.
However, because of this linkage, and because there are
other bugs suspected in the keyslot implementation, an
executive decision was made to disregard the key slot
feature in the chip.
The main downsides of this are:
- fewer slots (2048 vs 4096)
- no key access linkage to HMAC auth on SCE
I *think* that's it.
Fewer slots - 2048 slots is still a lot of slots, about half are
used now, I think this is plenty.
Key access linkage to HMAC auth on SCE - I have reasons to
suspect this feature is broken anyways for subtle reasons
related to malleability of the HMAC round constants. Even
without that brokenness, it's hard to use HMAC auth to manage
the system because it requires per-device unique keys: so,
we're using a PKI scheme and no symmetric secrets to handle
access controls.
Removing the key slots also greatly simplifies the code
base analytically. This culling removes the key slot
abstraction the "simple" way, but without the weirdness
of the keyslots (in particular the key ID chaining which
makes them different from data slots) I could remove even
more abstractions and simplify the code.
One upside is now all elements can enjoy the write mode
behavior which can force the slot to be only 0->1 writeable,
which could be useful for other things down the road.
This was tested to not interfere with Dabao-Alpha 0
bootloaders.
make it long enough that it's unlikely to have two identical
ones randomly connected to the same machine
but short enough that it's likely/conceivable to have a collision
there is a lock that happens in serial console interactions with
local echo where the instant feedback of a character entered causes
the USB object to be locked when the interrupt handler enters to
receive a character that was just sent.
The fix to this is to add the ability to disable interrupts before
entering a critical section (such as enqueuing data for a write)
and then re-enabling after tha section is done.
identify_flash_reset_qpi's behavior has been revised to
include setting all relevant parameters so that the device
that is identified behaves identically to the model device
(e.g. Macronix), to the extent that it is possible. This
includes setting the QE bit.
The routine to check QE has been renamed to `flash_ensure_eq()`
to reflect that it is safe to call multiple times: it checks
if the bit is already set, and if so, doesn't do anything.
Thus it can be routinely called without worry of wearing
out the device.
xtx devices still not fully working, but at least able to switch
in and out of spim modes in the face of uncertainty over which
device type is present.
rram handler for `std` requires the following additional features
over baremetal:
- mapped pages list, because a process has to "own" a page of RRAM
before writing to it. It's anticipated that the rram writer hardware is
"owned" by the keystore, so all write-access will be mediated by a
service in that PID
- irq-context handling of writes. this prevents writes from being
detached from their staging data, or other concurrent writes
from conflicting.
the more i test things the less confidence i have.
this fixes up a missing table entry in the table definition,
and then also adds a bypass routine - this is not actually
a hidden vulnerability, it's an explicit vulnerability until
the protect() routine is called. But it looks like we may have
to exploit it in order to transform our userstate in
the bootloader to one that has write-access to keys in order
to erase them in case of a developer boot.
the key setup seems to work correctly
but the data ACL setting doesn't "stick". The region
could be write-protected by some other element in the
CP/IFR config, need to dig a lot more. For now we need
to move on and crank out something to stick on the alpha
dabao boards...
'coreuser' is a slightly confusing term from the hardware
system because it's overloaded to mean some conceptually
related items that aren't implementation-wise essentially linked.
coreuser defines both some access protections on the main
array of the RRAM, and also some access protections on key
and data slots.
this patch includes some code that sets up the coreuser
functionality to a very simple scheme where just one PID
is trusted and the rest are not trusted. More complicated
schemes could be introduced with varying levels of trust
and dependencies but I like the analytical simplicity of
two states, so let's start there and complicate only when
absolutely necessary.
on dabao targets the duart is unavailable, so, it's convenient to
have a uart-based debug option in the HAL. this patch creates a
flag that can allow either target.
- add range checking to control access to main array or secure
array. This is purely a software enforced check, but it is in
theory backed by hardware gating that is a back stop in case
an adversary can gain arbitrary code access
- rework the rram primitive to return an error type
- add a `std` implementation stub. It is still missing an IRQ
context handler which ensures that all RRAM writes are atomic,
e.g. you can't take an interrupt in the middle of an RRAM
write because it would screw up the buffer staging.
auth_data actually changes with each signing operation (ostensibly
to prevent replay of signatures coming from tokens) so it has
to be presented as data parallel to the signature, instead of
as a static filed baked into the key header.
This commit revises the header record to reflect this organizatio
of data and also revises the signature check to be in-line
with the protocol.
have to absorb a version change due to xous-semver change
might as well also update the utra/svd generator dependencies
since that's been held off for a long time now.
this implements the API/HAL split on the HAL side, and also
reveals SPIM channel as a constant that can be just read out
so that spim accessors that need to build from raw parts
can do it without having to re-allocate IOs.
the top of memory is reserved for various security structures
the security structures do have some hardware protection
but life is better when we also help programmers avoid triggering
the protections by accident and then just being confused.
- combohash constants are moved to API: these need to be in a
dependency-free library so that we can refer to these values in
any context without creating circular dependencies
- sigcheck code is now put into the HAL layer, instead of in the
individual bootloaders. This is because the sigcheck code is re-usable
between boot0/boot1.
- sram timing trimming data has been entered from the XLS file
and put into an array for easy access
- more board initialization functions have been adedd, and cleaned
up to adhere to the rule that pin allocations don't change the state
of the pins, allowing pin allocation calls to be idemptoent (e.g.
you can call it several times without negative effects - the reason
being that the pin setups also return the pin maps, which can then
be passed to the functions of interest to manipulate the pin states)
The code base had evolved through several code names, interim
names, company names and chip names that alternatively did or did
not exist.
Baochip is the definitive name of the company, and the Baochip1x
(full part number BAO1X2S4F-WA) is the definitivey part number of
the SoC. For convenience, the part number is shortened to 'bao1x'
in most feature flags and variable references.
This commit fixes all of the odd names and removes some unmaintained
early targets.