mirror of
https://github.com/saymrwulf/xous-core.git
synced 2026-11-15 08:30:02 +00:00
add oled ui for baosec board targets on boot1
This commit is contained in:
parent
d80d6cbd6f
commit
e95550cb52
6 changed files with 233 additions and 4 deletions
|
|
@ -33,6 +33,8 @@ bao1x = [
|
|||
"bao1x-hal/loader-baosec",
|
||||
# "bao1x-hal/debug-print-usb",
|
||||
"bao1x-api",
|
||||
# needed for the boot logo
|
||||
"ux-api/loader-baosec",
|
||||
]
|
||||
unsafe-debug = []
|
||||
verbose-debug = ["bao1x-hal/debug-print-usb", "bao1x-hal/verbose-debug"]
|
||||
|
|
|
|||
BIN
bao1x-boot/boot1/src/font6x12_1bpp.raw
Normal file
BIN
bao1x-boot/boot1/src/font6x12_1bpp.raw
Normal file
Binary file not shown.
|
|
@ -17,10 +17,12 @@ use core::{
|
|||
|
||||
use bao1x_api::{BoardTypeCoding, BootWaitCoding};
|
||||
use bao1x_hal::{board::KeyPress, iox::Iox, usb::driver::UsbDeviceState};
|
||||
use bao1x_hal::{sh1107::Oled128x128, udma::GlobalConfig};
|
||||
use critical_section::Mutex;
|
||||
use platform::*;
|
||||
#[allow(unused_imports)]
|
||||
use utralib::*;
|
||||
use ux_api::minigfx::{DrawStyle, FrameBuffer, Point, Rectangle};
|
||||
|
||||
use crate::delay;
|
||||
use crate::platform::usb::glue;
|
||||
|
|
@ -61,7 +63,8 @@ pub unsafe extern "C" fn rust_entry() -> ! {
|
|||
one_way.get_decoded::<bao1x_api::BoardTypeCoding>().expect("Board type coding error");
|
||||
|
||||
crate::println_d!("TX_IDLE: {:?}", crate::platform::usb::TX_IDLE.load(Ordering::SeqCst));
|
||||
board_type = crate::platform::early_init(board_type);
|
||||
let perclk: u32;
|
||||
(board_type, perclk) = crate::platform::early_init(board_type);
|
||||
crate::println!("\n~~Boot1 up!~~\n");
|
||||
crate::println!("Configured board type: {:?}", board_type);
|
||||
|
||||
|
|
@ -95,14 +98,41 @@ pub unsafe extern "C" fn rust_entry() -> ! {
|
|||
crate::println!("Boot bypassed with keypress: {:?}", current_key);
|
||||
}
|
||||
|
||||
// grab a handle to the OLED if it exists on the board.
|
||||
let mut udma_global = GlobalConfig::new();
|
||||
let mut oled_iox = iox.clone();
|
||||
let mut oled = if board_type == BoardTypeCoding::Baosec {
|
||||
Some(bao1x_hal::sh1107::Oled128x128::new(
|
||||
bao1x_hal::sh1107::MainThreadToken::new(),
|
||||
perclk,
|
||||
&mut oled_iox,
|
||||
&mut udma_global,
|
||||
))
|
||||
} else {
|
||||
None
|
||||
};
|
||||
|
||||
let (se0_port, se0_pin) = match board_type {
|
||||
BoardTypeCoding::Baosec => bao1x_hal::board::setup_usb_pins(&iox),
|
||||
_ => crate::platform::setup_dabao_se0_pin(&iox),
|
||||
};
|
||||
iox.set_gpio_pin(se0_port, se0_pin, bao1x_api::IoxValue::Low); // put the USB port into SE0
|
||||
delay(500);
|
||||
delay(100);
|
||||
// use the USB disconnect time to initialize the display - at least 100ms is
|
||||
// needed after reset for the display to initialize
|
||||
if let Some(ref mut sh1107) = oled {
|
||||
// show the boot logo
|
||||
sh1107.init();
|
||||
sh1107.buffer_mut().fill(0xFFFF_FFFF);
|
||||
sh1107.blit_screen(&ux_api::bitmaps::baochip128x128::BITMAP);
|
||||
sh1107.draw();
|
||||
}
|
||||
delay(400);
|
||||
|
||||
// setup the USB port
|
||||
let (mut last_usb_state, mut portsc) = glue::setup();
|
||||
|
||||
// remainder of the 1-second total wait target time for USB disconnect
|
||||
delay(500);
|
||||
// release SE0
|
||||
iox.set_gpio_pin(se0_port, se0_pin, bao1x_api::IoxValue::High);
|
||||
|
|
@ -117,6 +147,9 @@ pub unsafe extern "C" fn rust_entry() -> ! {
|
|||
}
|
||||
// USB should have a solid shot of connecting now.
|
||||
crate::println!("USB device ready");
|
||||
if let Some(ref mut sh1107) = oled {
|
||||
marquee(sh1107, "Update mode");
|
||||
}
|
||||
|
||||
// provide some feedback on the run state of the BIO by peeking at the program counter
|
||||
// value, and provide feedback on the CPU operation by flashing the RGB LEDs.
|
||||
|
|
@ -145,6 +178,9 @@ pub unsafe extern "C" fn rust_entry() -> ! {
|
|||
crate::println!("USB is connected!");
|
||||
last_usb_state = new_usb_state;
|
||||
USB_CONNECTED.store(true, core::sync::atomic::Ordering::SeqCst);
|
||||
if let Some(ref mut sh1107) = oled {
|
||||
marquee(sh1107, "Connected");
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
|
|
@ -205,6 +241,41 @@ pub unsafe extern "C" fn rust_entry() -> ! {
|
|||
}
|
||||
}
|
||||
|
||||
if let Some(ref mut sh1107) = oled {
|
||||
marquee(sh1107, "Booting...");
|
||||
}
|
||||
|
||||
// when we get to this point, there's only two options...
|
||||
crate::secboot::boot_or_die();
|
||||
}
|
||||
|
||||
fn marquee(sh1107: &mut Oled128x128, msg: &str) {
|
||||
use bao1x_hal::sh1107::{COLUMN, ROW};
|
||||
use ux_api::bitmaps::baochip128x128::MARQUEE_BELOW;
|
||||
|
||||
// blank out the marquee
|
||||
ux_api::minigfx::op::rectangle(
|
||||
sh1107,
|
||||
Rectangle::new_with_style(
|
||||
Point::new(0, MARQUEE_BELOW as isize),
|
||||
Point::new(COLUMN, ROW),
|
||||
DrawStyle::new(ux_api::minigfx::PixelColor::Dark, ux_api::minigfx::PixelColor::Dark, 1),
|
||||
),
|
||||
None,
|
||||
false,
|
||||
);
|
||||
|
||||
// now try best-effort to fit the message. No word-wrapping here.
|
||||
let msg_width = msg.len() as isize * crate::gfx::CHAR_WIDTH;
|
||||
let x_pos = (COLUMN - msg_width) / 2;
|
||||
let y_midline = MARQUEE_BELOW as isize + (ROW - MARQUEE_BELOW as isize) / 2;
|
||||
let y_pos = y_midline - crate::gfx::CHAR_HEIGHT / 2;
|
||||
gfx::msg(
|
||||
sh1107,
|
||||
msg,
|
||||
Point::new(x_pos, y_pos),
|
||||
bao1x_hal::sh1107::Mono::White.into(),
|
||||
bao1x_hal::sh1107::Mono::Black.into(),
|
||||
);
|
||||
sh1107.draw();
|
||||
}
|
||||
|
|
|
|||
|
|
@ -1,6 +1,7 @@
|
|||
pub mod bao1x;
|
||||
pub use bao1x::*;
|
||||
pub mod debug;
|
||||
pub mod gfx;
|
||||
pub mod irq;
|
||||
pub mod usb;
|
||||
|
||||
|
|
|
|||
|
|
@ -69,7 +69,7 @@ pub fn setup_dabao_se0_pin<T: IoSetup + IoGpio>(iox: &T) -> (IoxPort, u8) {
|
|||
|
||||
/// This can change the board type coding to a safer, simpler board type if the declared board type has
|
||||
/// problems booting.
|
||||
pub fn early_init(mut board_type: bao1x_api::BoardTypeCoding) -> bao1x_api::BoardTypeCoding {
|
||||
pub fn early_init(mut board_type: bao1x_api::BoardTypeCoding) -> (bao1x_api::BoardTypeCoding, u32) {
|
||||
let iox = Iox::new(utra::iox::HW_IOX_BASE as *mut u32);
|
||||
|
||||
// setup board-specific I/Os - early boot set. These are items that have to be
|
||||
|
|
@ -172,6 +172,18 @@ pub fn early_init(mut board_type: bao1x_api::BoardTypeCoding) -> bao1x_api::Boar
|
|||
let (se0_port, se0_pin) = bao1x_hal::board::setup_usb_pins(&iox);
|
||||
iox.set_gpio_pin(se0_port, se0_pin, IoxValue::Low); // put the USB port into SE0 while we initialize things
|
||||
|
||||
// setup display - turn on its power, reset the framebuffer
|
||||
bao1x_hal::board::setup_display_pins(&iox);
|
||||
// power on
|
||||
let (oled_on_port, oled_on_pin) = bao1x_hal::board::setup_oled_power_pin(&iox);
|
||||
iox.set_gpio_pin_value(oled_on_port, oled_on_pin, IoxValue::High);
|
||||
// reset enable
|
||||
let (peri_rst_port, peri_reset_pin) = bao1x_hal::board::setup_periph_reset_pin(&iox);
|
||||
iox.set_gpio_pin_value(peri_rst_port, peri_reset_pin, IoxValue::Low);
|
||||
// delay for reset assert
|
||||
delay(1);
|
||||
iox.set_gpio_pin_value(peri_rst_port, peri_reset_pin, IoxValue::High);
|
||||
|
||||
// keyboard can setup at keyboard read time
|
||||
}
|
||||
}
|
||||
|
|
@ -226,7 +238,7 @@ pub fn early_init(mut board_type: bao1x_api::BoardTypeCoding) -> bao1x_api::Boar
|
|||
crate::debug::USE_CONSOLE.store(true, core::sync::atomic::Ordering::SeqCst);
|
||||
crate::println!("boot1 udma console up, CPU @ {}MHz!", fclk_freq / 2_000_000);
|
||||
|
||||
board_type
|
||||
(board_type, perclk)
|
||||
}
|
||||
|
||||
pub fn setup_timer(sysclk_freq: u32) {
|
||||
|
|
|
|||
143
bao1x-boot/boot1/src/platform/bao1x/gfx.rs
Normal file
143
bao1x-boot/boot1/src/platform/bao1x/gfx.rs
Normal file
|
|
@ -0,0 +1,143 @@
|
|||
#![allow(dead_code)]
|
||||
use bao1x_hal::sh1107::Mono;
|
||||
use ux_api::minigfx::*;
|
||||
|
||||
// The discipline for all the APIs in this module are that they act on a FrameBuffer which is
|
||||
// passed to the function. This allows us to bind the drawing computation on the caller-side of
|
||||
// of a shared frame buffer.
|
||||
|
||||
// this font is from the embedded graphics crate https://docs.rs/embedded-graphics/0.7.1/embedded_graphics/
|
||||
const FONT_IMAGE: &'static [u8] = include_bytes!("../../font6x12_1bpp.raw");
|
||||
pub const CHAR_HEIGHT: isize = 12;
|
||||
pub const CHAR_WIDTH: isize = 6;
|
||||
const FONT_IMAGE_WIDTH: isize = 96;
|
||||
const LEFT_MARGIN: isize = 10;
|
||||
|
||||
fn char_offset(c: char) -> isize {
|
||||
let fallback = ' ' as isize - ' ' as isize;
|
||||
if c < ' ' {
|
||||
return fallback;
|
||||
}
|
||||
if c <= '~' {
|
||||
return c as isize - ' ' as isize;
|
||||
}
|
||||
fallback
|
||||
}
|
||||
|
||||
pub fn msg<'a>(fb: &mut dyn FrameBuffer, text: &'a str, ll_pos: Point, fg: ColorNative, bg: ColorNative) {
|
||||
let mut ll_pos = ll_pos.clone();
|
||||
// this routine is adapted from the embedded graphics crate https://docs.rs/embedded-graphics/0.7.1/embedded_graphics/
|
||||
let char_per_row = FONT_IMAGE_WIDTH / CHAR_WIDTH;
|
||||
let mut idx = 0;
|
||||
let mut x_update = 0;
|
||||
for current_char in text.chars() {
|
||||
let mut char_walk_x = 0;
|
||||
let mut char_walk_y = 0;
|
||||
|
||||
loop {
|
||||
// Char _code_ offset from first char, most often a space
|
||||
// E.g. first char = ' ' (32), target char = '!' (33), offset = 33 - 32 = 1
|
||||
let char_offset = char_offset(current_char);
|
||||
let row = char_offset / char_per_row;
|
||||
|
||||
// Top left corner of character, in pixels
|
||||
let char_x = (char_offset - (row * char_per_row)) * CHAR_WIDTH;
|
||||
let char_y = row * CHAR_HEIGHT;
|
||||
|
||||
// Bit index
|
||||
// = X pixel offset for char
|
||||
// + Character row offset (row 0 = 0, row 1 = (192 * 8) = 1536)
|
||||
// + X offset for the pixel block that comprises this char
|
||||
// + Y offset for pixel block
|
||||
let bitmap_bit_index =
|
||||
char_x + (FONT_IMAGE_WIDTH * char_y) + char_walk_x + (char_walk_y * FONT_IMAGE_WIDTH);
|
||||
|
||||
let bitmap_byte = bitmap_bit_index / 8;
|
||||
let bitmap_bit = 7 - (bitmap_bit_index % 8);
|
||||
|
||||
let color = if FONT_IMAGE[bitmap_byte as usize] & (1 << bitmap_bit) != 0 { fg } else { bg };
|
||||
|
||||
let x = ll_pos.x + CHAR_WIDTH * idx + char_walk_x;
|
||||
let y = ll_pos.y + char_walk_y;
|
||||
|
||||
// draw color at x, y
|
||||
if (current_char as u8 != 0xd) && (current_char as u8 != 0xa) {
|
||||
// don't draw CRLF specials
|
||||
fb.put_pixel(Point::new(x, y), color);
|
||||
}
|
||||
|
||||
char_walk_x += 1;
|
||||
|
||||
if char_walk_x >= CHAR_WIDTH {
|
||||
char_walk_x = 0;
|
||||
char_walk_y += 1;
|
||||
|
||||
// Done with this char, move on to the next one
|
||||
if char_walk_y >= CHAR_HEIGHT {
|
||||
if current_char as u8 == 0xd {
|
||||
// '\n'
|
||||
ll_pos.y += CHAR_HEIGHT;
|
||||
} else if current_char as u8 == 0xa {
|
||||
// '\r'
|
||||
ll_pos.x = LEFT_MARGIN;
|
||||
x_update = 0;
|
||||
} else {
|
||||
idx += 1;
|
||||
x_update += CHAR_WIDTH;
|
||||
}
|
||||
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
ll_pos.x += x_update;
|
||||
}
|
||||
|
||||
pub fn line(fb: &mut dyn FrameBuffer, l: Line, clip: Option<Rectangle>, xor: bool) {
|
||||
let color: ColorNative;
|
||||
if l.style.stroke_color.is_some() {
|
||||
color = l.style.stroke_color.unwrap().into();
|
||||
} else {
|
||||
return;
|
||||
}
|
||||
let mut x0 = l.start.x;
|
||||
let mut y0 = l.start.y;
|
||||
let x1 = l.end.x;
|
||||
let y1 = l.end.y;
|
||||
|
||||
let dx = (x1 - x0).abs();
|
||||
let sx = if x0 < x1 { 1 } else { -1 };
|
||||
let dy = -((y1 - y0).abs());
|
||||
let sy = if y0 < y1 { 1 } else { -1 };
|
||||
let mut err = dx + dy; // error value e_xy
|
||||
loop {
|
||||
if x0 >= 0 && y0 >= 0 && x0 < (fb.dimensions().x as _) && y0 < (fb.dimensions().y as _) {
|
||||
if clip.is_none() || (clip.unwrap().intersects_point(Point::new(x0, y0))) {
|
||||
if !xor {
|
||||
fb.put_pixel(Point::new(x0 as _, y0 as _), color);
|
||||
} else {
|
||||
if let Some(existing) = fb.get_pixel(Point::new(x0 as _, y0 as _)) {
|
||||
if existing == Mono::Black.into() {
|
||||
fb.put_pixel(Point::new(x0 as _, y0 as _), Mono::White.into());
|
||||
} else {
|
||||
fb.put_pixel(Point::new(x0 as _, y0 as _), Mono::Black.into());
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
if x0 == x1 && y0 == y1 {
|
||||
break;
|
||||
}
|
||||
let e2 = 2 * err;
|
||||
if e2 >= dy {
|
||||
err += dy;
|
||||
x0 += sx;
|
||||
}
|
||||
if e2 <= dx {
|
||||
err += dx;
|
||||
y0 += sy;
|
||||
}
|
||||
}
|
||||
}
|
||||
Loading…
Reference in a new issue