pretty-print spi

This commit is contained in:
bunnie 2024-06-01 21:58:05 +08:00
parent ccc342d9f3
commit e0f3ee8e49

View file

@ -4,8 +4,7 @@ use super::report_api;
use crate::*;
pub fn spi_test() {
report_api(0x1310_5000);
report_api(0x51C0_0000);
print!("SPI test\r");
// clear prior test config state
let mut test_cfg = CSR::new(utra::main::HW_MAIN_BASE as *mut u32);
@ -15,7 +14,7 @@ pub fn spi_test() {
// stop all the machines, so that code can be loaded
bio_ss.bio.wo(utra::bio::SFR_CTRL, 0x0);
let code = spi_driver();
report_api(code.len() as u32);
print!("code length {}\r", code.len());
bio_ss.load_code(code, 0);
// configure fifo trigger levels
@ -36,7 +35,7 @@ pub fn spi_test() {
bio_ss.bio.wo(
utra::bio::SFR_CONFIG,
bio_ss.bio.ms(utra::bio::SFR_CONFIG_SNAP_OUTPUT_TO_QUANTUM, 1)
| bio_ss.bio.ms(utra::bio::SFR_CONFIG_SNAP_OUTPUT_TO_WHICH, 2)
| bio_ss.bio.ms(utra::bio::SFR_CONFIG_SNAP_OUTPUT_TO_WHICH, 2),
);
// bypass sync on all but clock
@ -45,7 +44,7 @@ pub fn spi_test() {
bio_ss.bio.wo(
utra::bio::SFR_EXTCLOCK,
bio_ss.bio.ms(utra::bio::SFR_EXTCLOCK_USE_EXTCLK, 0b1000)
| bio_ss.bio.ms(utra::bio::SFR_EXTCLOCK_EXTCLK_GPIO_3, 9)
| bio_ss.bio.ms(utra::bio::SFR_EXTCLOCK_EXTCLK_GPIO_3, 9),
);
// start cores 2 & 3
@ -75,10 +74,10 @@ pub fn spi_test() {
while bio_ss.bio.rf(SFR_FLEVEL_PCLK_REGFIFO_LEVEL1) == 0 {} // wait until there's something there
retvals[j] = bio_ss.bio.r(utra::bio::SFR_RXF1);
j += 1;
report_api(j as u32);
print!("iter {}", j);
}
for (index, &val) in retvals.iter().enumerate() {
report_api(val);
print!("SPI rbk {:x}", val);
// the XOR to 0xAAAA is just a mask we threw in to test immediate loads
assert!(val == ((0xAA00 | index as u32) ^ 0xAAAA));
}
@ -90,10 +89,10 @@ pub fn spi_test() {
// - loading word out of RAM (the random mask at the top)
// - machine ID based dispatch
// - how fast the SPI could run, hence the unrolled loop
// - Receive clock triggering a code event (quanta register x20
// is remapped to a GPIO input instead of the clock divider)
// - Branch on quanta read (saves one clock cycle for a tight loop;
// not strictly necessary but we use the idiom here to cap Tx loop)
// - Receive clock triggering a code event (quanta register x20 is remapped to a GPIO input instead of the
// clock divider)
// - Branch on quanta read (saves one clock cycle for a tight loop; not strictly necessary but we use the
// idiom here to cap Tx loop)
// This runs at about a 25MHz SPI clock rate, assuming an 800MHz
// core clock for the complex. The Rx loop is potentially much faster
// than the Tx loop.