mirror of
https://github.com/saymrwulf/xous-core.git
synced 2026-11-15 08:30:02 +00:00
commit
d116509a5a
2 changed files with 84 additions and 0 deletions
|
|
@ -142,6 +142,7 @@ pub fn setup() -> (UsbDeviceState, u32) {
|
|||
}
|
||||
|
||||
pub fn shutdown() {
|
||||
crate::debug::USE_CONSOLE.store(false, core::sync::atomic::Ordering::SeqCst);
|
||||
unsafe {
|
||||
if let Some(ref mut usb_ref) = crate::platform::bao1x::usb::USB {
|
||||
let usb = &mut *core::ptr::addr_of_mut!(*usb_ref);
|
||||
|
|
|
|||
|
|
@ -462,6 +462,89 @@ impl Repl {
|
|||
}
|
||||
}
|
||||
}
|
||||
"baosec-init" => {
|
||||
// this routine is used to initialize baosec products - sets the board type and
|
||||
// erases the off-chip FLASH
|
||||
use bao1x_api::{baosec::PDDB_LEN, baosec::PDDB_ORIGIN};
|
||||
use bao1x_hal::{
|
||||
board::SPINOR_BULK_ERASE_SIZE,
|
||||
ifram::IframRange,
|
||||
iox::Iox,
|
||||
udma::{Spim, *},
|
||||
};
|
||||
let perclk = 100_000_000;
|
||||
let udma_global = GlobalConfig::new();
|
||||
|
||||
// setup the I/O pins
|
||||
let iox = Iox::new(utralib::generated::HW_IOX_BASE as *mut u32);
|
||||
let channel = bao1x_hal::board::setup_memory_pins(&iox);
|
||||
udma_global.clock_on(PeriphId::from(channel));
|
||||
// safety: this is safe because clocks have been set up
|
||||
let mut flash_spim = unsafe {
|
||||
Spim::new_with_ifram(
|
||||
channel,
|
||||
// has to be half the clock frequency reaching the block, but
|
||||
// run it as fast
|
||||
// as we can run perclk
|
||||
perclk / 4,
|
||||
perclk / 2,
|
||||
SpimClkPol::LeadingEdgeRise,
|
||||
SpimClkPha::CaptureOnLeading,
|
||||
SpimCs::Cs0,
|
||||
0,
|
||||
0,
|
||||
None,
|
||||
256 + 16, /* just enough space to send commands + programming
|
||||
* page */
|
||||
4096,
|
||||
Some(6),
|
||||
Some(SpimMode::Standard), // guess Standard
|
||||
IframRange::from_raw_parts(
|
||||
bao1x_hal::board::SPIM_FLASH_IFRAM_ADDR,
|
||||
bao1x_hal::board::SPIM_FLASH_IFRAM_ADDR,
|
||||
4096 * 2,
|
||||
),
|
||||
)
|
||||
};
|
||||
flash_spim.identify_flash_reset_qpi();
|
||||
let flash_id = flash_spim.mem_read_id_flash();
|
||||
crate::println!("flash ID (init): {:x}", flash_id);
|
||||
if !SPI_FLASH_IDS.contains(&(flash_id & 0xFF_FF_FF)) {
|
||||
return Err(Error::help("Supported SPI device not found. Aborting operation."));
|
||||
}
|
||||
|
||||
crate::println!("Erasing from {:x}-{:x}...", 0, PDDB_ORIGIN + PDDB_LEN);
|
||||
for addr in (0..PDDB_ORIGIN + PDDB_LEN).step_by(SPINOR_BULK_ERASE_SIZE as usize) {
|
||||
crate::println!(" {:x}...", addr);
|
||||
flash_spim.flash_erase_block(addr, SPINOR_BULK_ERASE_SIZE as usize);
|
||||
}
|
||||
crate::println!("...done!");
|
||||
let one_way = bao1x_hal::acram::OneWayCounter::new();
|
||||
let board_type =
|
||||
one_way.get_decoded::<bao1x_api::BoardTypeCoding>().expect("Board type coding error");
|
||||
if board_type != bao1x_api::BoardTypeCoding::Baosec {
|
||||
while one_way.get_decoded::<bao1x_api::BoardTypeCoding>().expect("owc coding error")
|
||||
!= bao1x_api::BoardTypeCoding::Baosec
|
||||
{
|
||||
one_way.inc_coded::<bao1x_api::BoardTypeCoding>().expect("increment error");
|
||||
}
|
||||
}
|
||||
// reset the USB stack so that we'll re-enumerate correctly after this reboot.
|
||||
// This also has the side-effect of redirecting the console output back to the serial port.
|
||||
crate::platform::usb::glue::shutdown();
|
||||
let (se0_port, se0_pin) = bao1x_hal::board::setup_usb_pins(&iox);
|
||||
iox.set_gpio_dir(se0_port, se0_pin, bao1x_api::IoxDir::Output);
|
||||
iox.set_gpio_pin(se0_port, se0_pin, bao1x_api::IoxValue::Low); // put the USB port into SE0, so we re-enumerate with the OS stack
|
||||
|
||||
use bao1x_hal::board::{BOOKEND_END, BOOKEND_START};
|
||||
// CI note: this appears on the "hard UART", not on USB serial. If we want this on USB
|
||||
// serial, we would want to add some wait time to ensure the USB packets get sent before
|
||||
// issuing the reboot command.
|
||||
crate::println!("{}BOOT1.SETBOARD,{}", BOOKEND_START, BOOKEND_END);
|
||||
crate::println!("Board type set to baosec, rebooting so boot1 can provision keys!");
|
||||
let mut rcurst = CSR::new(utra::sysctrl::HW_SYSCTRL_BASE as *mut u32);
|
||||
rcurst.wo(utra::sysctrl::SFR_RCURST0, 0x55AA);
|
||||
}
|
||||
#[cfg(feature = "test-boot0-keys")]
|
||||
"publock" => {
|
||||
let rram = CSR::new(utra::rrc::HW_RRC_BASE as *mut u32);
|
||||
|
|
|
|||
Loading…
Reference in a new issue