fix a few minor details missing in the tests

also update docs and completion tracker
This commit is contained in:
bunnie 2024-03-12 13:54:07 +08:00
parent 4fa3dd3b59
commit 133bb2b74f
3 changed files with 23 additions and 6 deletions

View file

@ -102,18 +102,18 @@ pub fn bio_tests() {
// -[x] Host FIFO stall on empty test. Core stalls until host provides data.
// -[x] Host FIFO stall on full test. Core stall until host reads data.
// -[x] GPIO input path test
// -[ ] Extclk as x20 stall source
// -[ ] Check Extclk:gpio pin mapping (make sure bit ordering is not swapped)
// -[x] Extclk as x20 stall source
// -[x] Check Extclk:gpio pin mapping (make sure bit ordering is not swapped)
// -[ ] GPIO direction control test
// -[ ] FIFO level trigger test - eq, gt, lt on various channels, at various fullness levels
// -[x] Stall on event - register bit test, between cores
// -[x] Stall on event - register bit test, to host
// -[x] Stall on event - FIFO level test
// -[ ] Host IRQ generation test - some combination with event tests above to confirm IRQ generation
// -[ ] Core ID read test
// -[x] Core ID read test
// -[ ] Core aclk counter test
// Application tests:
// -[ ] SPI loopback test - implement using extclk as spi clk for input
// -[x] SPI loopback test - implement using extclk as spi clk for input
// -[ ] I2C loopback test
// -[ ] IR controller test
// -[ ] Arithmetic test, utilizing load/store on core 0

View file

@ -33,7 +33,11 @@ pub fn spi_test() {
// this actually shouldn't matter, but set it to be "fast" for testing
bio_ss.bio.wo(utra::bio::SFR_QDIV3, 0x1_0000);
// snap GPIO outputs
bio_ss.bio.wo(utra::bio::SFR_CONFIG, 1);
bio_ss.bio.wo(
utra::bio::SFR_CONFIG,
bio_ss.bio.ms(utra::bio::SFR_CONFIG_SNAP_OUTPUT_TO_QUANTUM, 1)
| bio_ss.bio.ms(utra::bio::SFR_CONFIG_SNAP_OUTPUT_TO_WHICH, 2)
);
// bypass sync on all but clock
bio_ss.bio.wo(utra::bio::SFR_SYNC_BYPASS, 0x500);
@ -82,6 +86,17 @@ pub fn spi_test() {
report_api(0x51C0_600D);
}
// This is written to also test some additional features:
// - loading word out of RAM (the random mask at the top)
// - machine ID based dispatch
// - how fast the SPI could run, hence the unrolled loop
// - Receive clock triggering a code event (quanta register x20
// is remapped to a GPIO input instead of the clock divider)
// - Branch on quanta read (saves one clock cycle for a tight loop;
// not strictly necessary but we use the idiom here to cap Tx loop)
// This runs at about a 25MHz SPI clock rate, assuming an 800MHz
// core clock for the complex. The Rx loop is potentially much faster
// than the Tx loop.
#[rustfmt::skip]
bio_code!(
spi_driver,

View file

@ -51,7 +51,7 @@ pub fn hello_multiverse() {
bio_ss.bio.wo(
utra::bio::SFR_CONFIG,
bio_ss.bio.ms(utra::bio::SFR_CONFIG_SNAP_OUTPUT_TO_QUANTUM, 1)
| bio_ss.bio.ms(utra::bio::SFR_CONFIG_SNAP_OUTPUT_TO_QUANTUM, 2), /* arbitrary choice, they
| bio_ss.bio.ms(utra::bio::SFR_CONFIG_SNAP_OUTPUT_TO_QUANTUM, 1), /* arbitrary choice, they
* should all be the same */
);
// start all the machines, all at once
@ -236,6 +236,8 @@ pub fn host_fifo_tests() {
bio_ss.bio.wo(utra::bio::SFR_CTRL, 0x0);
let code = fifo_host_bitbang();
bio_ss.load_code(code, 0);
// reset all the fifos
bio_ss.bio.wo(utra::bio::SFR_FIFO_CLR, 0xF);
// configure & run the 0th machine
// clock it slowly, so the fifo builds up back pressure