diff --git a/bao1x-boot/boot1/src/platform/bao1x/bao1x.rs b/bao1x-boot/boot1/src/platform/bao1x/bao1x.rs index 6b8e6f29c..7e4695986 100644 --- a/bao1x-boot/boot1/src/platform/bao1x/bao1x.rs +++ b/bao1x-boot/boot1/src/platform/bao1x/bao1x.rs @@ -249,6 +249,72 @@ pub fn early_init(mut board_type: bao1x_api::BoardTypeCoding) -> (bao1x_api::Boa // power on iox.set_gpio_pin_value(oled_on_port, oled_on_pin, IoxValue::High); + + #[cfg(feature = "alt-boot1")] + { + crate::println!("entering pddb_erase"); + // setup all the board pins to a known state + let iox = Iox::new(utra::iox::HW_IOX_BASE as *mut u32); + bao1x_hal::board::setup_memory_pins(&iox); + + // this routine is used to initialize baosec products - sets the board type and + // erases the off-chip FLASH + use bao1x_api::baosec::PDDB_ORIGIN; + use bao1x_hal::{ + board::SPINOR_BULK_ERASE_SIZE, + ifram::IframRange, + iox::Iox, + udma::{Spim, *}, + }; + let perclk = 100_000_000; + let udma_global = GlobalConfig::new(); + + // setup the I/O pins + let channel = bao1x_hal::board::setup_memory_pins(&iox); + udma_global.clock_on(bao1x_api::PeriphId::from(channel)); + // safety: this is safe because clocks have been set up + let mut flash_spim = unsafe { + Spim::new_with_ifram( + channel, + // has to be half the clock frequency reaching the block, but + // run it as fast + // as we can run perclk + perclk / 4, + perclk / 2, + SpimClkPol::LeadingEdgeRise, + SpimClkPha::CaptureOnLeading, + SpimCs::Cs0, + 0, + 0, + None, + 256 + 16, /* just enough space to send commands + programming + * page */ + 4096, + Some(6), + Some(SpimMode::Standard), // guess Standard + IframRange::from_raw_parts( + bao1x_hal::board::SPIM_FLASH_IFRAM_ADDR, + bao1x_hal::board::SPIM_FLASH_IFRAM_ADDR, + 4096 * 2, + ), + ) + }; + flash_spim.identify_flash_reset_qpi(); + let flash_id = flash_spim.mem_read_id_flash(); + crate::println!("flash ID (init): {:x}", flash_id); + if bao1x_api::SPI_FLASH_IDS.contains(&(flash_id & 0xFF_FF_FF)) { + let pddb_erase_len = SPINOR_BULK_ERASE_SIZE as usize * 2; + for addr in + (PDDB_ORIGIN..PDDB_ORIGIN + pddb_erase_len).step_by(SPINOR_BULK_ERASE_SIZE as usize) + { + crate::println!(" {:x}...", addr); + flash_spim.flash_erase_block(addr, SPINOR_BULK_ERASE_SIZE as usize); + } + crate::println!("...done!"); + } else { + crate::println!("...skipped, couldn't find FLASH part"); + } + } } #[cfg(not(feature = "oem"))] BoardTypeCoding::Oem => {