improve reset condition for filter & make pass criteria tighter

- filter setup can be impacted by previous engine running, make
sure engines are stopped and FIFOs flushed prior to test start
- when reading a filtered bank we can get garbage, so make the
test check for the specific value we should see.
This commit is contained in:
bunnie 2024-09-26 18:18:12 +08:00
parent 81f0523ee3
commit 0b419400c7

View file

@ -49,11 +49,19 @@ pub fn dma_filter_off() {
pub fn filter_test() -> usize {
print!("==Filter test==\r");
// clear any prior test config state
let mut test_cfg = CSR::new(utra::csrtest::HW_CSRTEST_BASE as *mut u32);
test_cfg.wo(utra::csrtest::WTEST, 0);
let mut passing = true;
use utralib::generated::HW_SRAM_MEM as RAM_BASE;
use utralib::generated::HW_SRAM_MEM_LEN as RAM_SIZE;
let mut bio_ss = BioSharedState::new();
bio_ss.bio.wo(utra::bio_bdma::SFR_CTRL, 0x0);
// reset all the fifos
bio_ss.bio.wo(utra::bio_bdma::SFR_FIFO_CLR, 0xF);
// enable the filters
bio_ss.bio.rmwf(utra::bio_bdma::SFR_CONFIG_DISABLE_FILTER_MEM, 0);
bio_ss.bio.rmwf(utra::bio_bdma::SFR_CONFIG_DISABLE_FILTER_PERI, 0);
@ -85,6 +93,14 @@ pub fn filter_test() -> usize {
// *** increments 3 ret values total
// - access to the BIO_BDMA registers: try to disable the filters.
print!("attempt to violate peri filter\r");
if bio_ss.bio.rf(utra::bio_bdma::SFR_CONFIG_DISABLE_FILTER_MEM) != 0 {
passing = false;
print!("peri range filter pre-condition fail A\r");
}
if bio_ss.bio.rf(utra::bio_bdma::SFR_CONFIG_DISABLE_FILTER_PERI) != 0 {
passing = false;
print!("peri range filter pre-condition fail B\r");
}
cache_flush();
let naughty_dma_ptr: &mut [u32] = unsafe {
core::slice::from_raw_parts_mut(
@ -102,11 +118,11 @@ pub fn filter_test() -> usize {
// check that the values did not change
if bio_ss.bio.rf(utra::bio_bdma::SFR_CONFIG_DISABLE_FILTER_MEM) != 0 {
passing = false;
print!("peri range filter FAIL\r");
print!("peri range filter FAIL A\r");
}
if bio_ss.bio.rf(utra::bio_bdma::SFR_CONFIG_DISABLE_FILTER_PERI) != 0 {
passing = false;
print!("peri range filter FAIL\r");
print!("peri range filter FAIL B\r");
}
// attempt to read the config word
bio_ss.bio.wo(
@ -117,9 +133,12 @@ pub fn filter_test() -> usize {
bio_ss.bio.wo(utra::bio_bdma::SFR_TXF0, 4); // initiate a single transfer
while bio_ss.bio.r(utra::bio_bdma::SFR_EVENT_STATUS) & 0x1 == 0 {}
cache_flush();
if target[0] != 0x0 {
let tval = target[0];
if tval == 0x1000_0408 {
passing = false;
print!("peri range read filter FAIL\r")
print!("peri range read filter FAIL target[0]->{:x} got a correct value of 0x10000408\r", tval);
} else {
print!("CFGINFO returned {:x}, != 0x10000408\r", tval);
}
print!("peri violation test done\r");