uhd/host/docs/dpdk.dox

/*! \page page_dpdk DPDK, Data Plane Development Kit

\tableofcontents

\section dpdk_overview DPDK Overview

Data Plane Development Kit (DPDK) is a set of libraries that allows network
interface controller (NIC) drivers to use user space memory buffers to send and
receive data over a network. These libraries underpin one of the network
transport options in UHD.

In UHD, the DPDK-based transport will fork off I/O threads that implement the
network services, and these I/O threads will service the NICs on cores provided
in your configuration. The cores will be completely consumed by the I/O thread.
Together with DPDK's polling-mode drivers, this virtually eliminates context
switching in UHD's transport layer, which enables us to stream higher sample
rates.

\section dpdk_setup DPDK Setup

DPDK is currently only available on Linux platforms, requires an input-output
memory management unit (IOMMU), and must be run on a multicore processor. The
following subsections will talk through the steps required to setup DPDK on your
computer.

\subsection dpdk_installation DPDK Installation Instructions

As a new and developing technology, the DPDK APIs are unstable. UHD requires
version 17.11.

On Ubuntu 18.04/18.10, Fedora 28/29, or Debian Stretch (via backports), DPDK is
available in your distribution's repositories. For example, on Debian systems,
it can be obtained with the following command:

    sudo apt install dpdk dpdk-dev

Otherwise, you'll need to follow the build guide at
https://doc.dpdk.org/guides-17.11/linux_gsg/build_dpdk.html . The software
releases can be found at https://core.dpdk.org/download/.

\subsection dpdk_system_configuration System Configuration

The official documentation regarding system configuration can be found at
https://doc.dpdk.org/guides-17.11/linux_gsg/sys_reqs.html.

First, you'll need to enable the IOMMU and set up some hugepages. DPDK will
completely take over all available hugepages, so don't allocate all your memory
to them- the rest of UHD and the application need memory too.

For example, on a system with 16 GB of RAM, a generous appropriation of
512x 2 MiB pages was more than sufficient, and you likely won't need that much.

For best results, hugepages should be enabled at boot. For example, using an
Intel IOMMU with Ubuntu 18.04 IOMMU drivers, the following line was needed in
our Grub config.

    iommu=pt intel_iommu=on hugepages=2048

The setup of the IOMMU and hugepages is system-specific, so consult the kernel
documentation for more info. After you reboot, you should see
`/sys/kernel/iommu_groups` populated.

Next, many of the NIC drivers are implemented atop `vfio-pci`, so you'll need to
load that driver with the following command:

    modprobe vfio-pci

For NICs that require vfio-pci (like Intel's X520), you'll want to use the
`dpdk-devbind.py` script to the vfio-pci driver.
See https://doc.dpdk.org/guides-17.11/linux_gsg/linux_drivers.html#binding-and-unbinding-network-ports-to-from-the-kernel-modules
for more details.

With the hugepages, IOMMU, and drivers set up, the system is ready for DPDK to
use.

\subsection dpdk_nic_config NIC Configuration

Configuration of the NIC can be controlled via device arguments via the usual
methods, but the \ref page_configfiles "UHD configuration file" is the
recommended location.

In order to run, you'll need to set the permissions for your user to take over
the vfio-pci devices, the hugepages, and the scheduler's settings for the
threads (at a minimum). You may consider running you applications as root, at
least while becoming familiar with DPDK. If you use a per-user config file, make
sure it's in the correct location.

The config file will have 2 different components. First are the global DPDK
options:

    ;When present in device args, use_dpdk indicates you want DPDK to take over the UDP transports
    ;The value here represents a config, so you could have another section labeled use_dpdk=myconf
    ;instead and swap between them
    [use_dpdk=1]
    ;dpdk-mtu is the NIC's MTU setting
    ;This is separate from MPM's maximum packet size--tops out at 4000
    dpdk-mtu=9000
    ;dpdk-driver is the -d flag for the DPDK EAL. If DPDK doesn't pick up the driver for your NIC
    ;automatically, you may need this argument to point it to the folder where it can find the drivers
    ;Note that DPDK will attempt to load _everything_ in that folder as a driver, so you may want to
    ;create a separate folder with symlinks to the librte_pmd_* and librte_mempool_* libraries.
    dpdk-driver=/usr/local/lib/dpdk-pmds/
    ;dpdk-corelist is the -l flag for the DPDK EAL. See more at the link
    ; https://doc.dpdk.org/guides-17.11/linux_gsg/build_sample_apps.html#running-a-sample-application
    dpdk-corelist=0,1
    ;dpdk-num-mbufs is the total number of packet buffers allocated
    ;to each direction's packet buffer pool
    ;This will be multiplied by the number of NICs, but NICs on the same
    ;CPU socket share a pool
    dpdk-num-mbufs=4095
    ;dpdk-mbuf-cache-size is the number of buffers to cache for a CPU
    ;The cache reduces the interaction with the global pool
    dpdk-mbuf-cache-size=315


The other sections fall under per-NIC arguments. The key for NICs is the MAC
address, and it must be in a particular format. Hex digits must all be lower
case, and octets must be separated by colons. Here is an example:

    [dpdk-mac=3c:fd:fe:a2:a9:09]
    ;dpdk-io-cpu selects the CPU that this NIC's driver will run on
    ;Multiple NICs may occupy one CPU, but the I/O thread will completely
    ;consume that CPU. Also, 0 is reserved for the master thread (i.e.
    ;the initial UHD thread that calls init() for DPDK). Attempting to
    ;use it as an I/O thread will only result in hanging.
    dpdk-io-cpu = 1
    ;dpdk-ipv4 specifies the IPv4 address, and both the address and
    ;subnet mask are required (and in this format!). DPDK uses the
    ;netmask to create a basic routing table. Routing to other networks
    ;(i.e. via gateways) is not permitted.
    dpdk-ipv4 = 192.168.10.1/24

    [dpdk-mac=3c:fd:fe:a2:a9:0a]
    dpdk-io-cpu = 1
    dpdk-ipv4 = 192.168.20.1/24

\section dpdk_using Using DPDK in UHD

Once DPDK is installed and configured on your system, it can be used with UHD.
The following steps will describe how to stream using DPDK. DPDK is currently
only available on the following devices:

- \ref page_usrp_e3xx "E320 (but not E31x) device"
- \ref page_usrp_n3xx "N3xx devices"
- \ref page_usrp_x3x0 "X3xx devices"

\subsection dpdk_device_args Enabling DPDK with UHD Device Args

Add the following to your device args in order to indicate that a DPDK-based UDP
transport shall be used instead of the kernel's UDP stack.

    --args="use_dpdk=1"

Device discovery via DPDK is not currently implemented, so the device args
`mgmt_addr`, `addr`, and `second_addr` (if applicable) must all be specified at
runtime. There is no mechanism for MPM's TCP/IP control traffic to flow over a
link that is occupied by DPDK, so mgmt_addr must point to a link that is not
used for CHDR, such as N310's RJ45 port.

*/
// vim:ft=doxygen: