uhd/host/docs/general.dox

/*! \page page_general General Application Notes

\tableofcontents

\section general_tuning Tuning Notes

\subsection general_tuning_process Two-stage tuning process

A USRP device has two stages of tuning:

- RF front-end: translates bewteen RF and IF
- DSP: translates between IF and baseband

In a typical use-case, the user specifies an overall center frequency
for the signal chain. The RF front-end will be tuned as close as
possible to the center frequency, and the DSP will account for the error
in tuning between target frequency and actual frequency. The user may
also explicitly control both stages of tuning through through the **tune_request_t** object, which allows for more advanced tuning.

In general, Using UHD software's advanced tuning is highly recommended
as it makes it easy to move the DC component out of your
band-of-interest. This can be done by passing your desired LO offset to
the **tune_request_t** object, and letting the UHD software handle the
rest.

The **tune_request_t** object can also be used with certain
daughterboards to use Integer-N tuning instead of the default fractional
tuning, allowing for better spur performance. The daughterboards that
support this functionality are:

- WBX (all revisions)
- WBX-120
- SBX (all revisions)
- SBX-120
- CBX
- CBX-120

\subsubsection general_tuning_rxchain Tuning the receive chain:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~{.cpp}
//tuning to a desired center frequency
usrp->set_rx_freq(target_frequency_in_hz);

--OR--

//advanced tuning with tune_request_t uhd::tune_request_t
tune_req(target_frequency_in_hz, desired_lo_offset);
tune_req.args = uhd::device_addr_t("mode_n=integer"); //to use Int-N tuning
//fill in any additional/optional tune request fields...
usrp->set_rx_freq(tune_req);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

More information can be found in uhd::tune_request_t.

\subsection general_tuning_rfsettling RF front-end settling time

After tuning, the RF front-end will need time to settle into a usable
state. Typically, this means that the local oscillators must be given
time to lock before streaming begins. Lock time is not consistent; it
varies depending upon the device and requested settings. After tuning
and before streaming, the user should wait for the **lo_locked** sensor
to become true or sleep for a conservative amount of time (perhaps a
second).

\subsubsection general_tuning_waitcode Pseudo-code for dealing with settling time after tuning on receive:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~{.cpp}
    usrp->set_rx_freq(...);
    sleep(1);
    usrp->issue_stream_command(...);

    --OR--

    usrp->set_rx_freq(...);
    while (not usrp->get_rx_sensor("lo_locked").to_bool()){
        //sleep for a short time in milliseconds
    }
    usrp->issue_stream_command(...);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

\section general_subdev Specifying the Subdevice to Use

A subdevice specification string for USRP family devices is composed of:

    <motherboard slot name>:<daughterboard frontend name>

Ex: The subdev spec markup string to select a WBX on slot B.

    B:0

Ex: The subdev spec markup string to select a BasicRX on slot B.

    B:AB

    -- OR --

    B:A

    -- OR --

    B:B

\subsection general_subdev_slotnames USRP Family Motherboard Slot Names

All USRP family motherboards have a first slot named **A:**. The USRP1 and the X3x0
have two daughterboard subdevice slots, known as **A:** and **B:**.

\subsection general_subdev_dbnames Daughterboard Frontend Names

Daughterboard frontend names can be used to specify which signal path is
used from a daughterboard. Most daughterboards have only one frontend **:0**.
A few daughterboards (Basic, LF and TVRX2) have multiple
frontend names available. The frontend names are documented in \ref page_dboards.

\section general_ounotes Overflow/Underflow Notes

<b>Note:</b> The following overflow/underflow notes do not apply to USRP1,
which does not support the advanced features available in newer
products.

\subsection general_ounotes_overflow Overflow notes

When receiving, the device produces samples at a constant rate.
Overflows occurs when the host does not consume data fast enough. When
UHD software detects the overflow, it prints an "O" or "D" to stdout,
and pushes an inline message packet into the receive stream.

<b>Network-based devices</b>: The host does not back-pressure the receive
stream. When the kernel's socket buffer becomes full, it will drop
subsequent packets. UHD software detects the overflow as a discontinuity
in the packet's sequence numbers, and pushes an inline message packet
into the receive stream. In this case the character "D" is printed to
stdout as an indication.

<b>Other devices</b>: The host back-pressures the receive stream.
Therefore, overflows always occur in the device itself. When the
device's internal buffers become full, streaming is shut off, and an
inline message packet is sent to the host. In this case the character
"O" is printed to stdout as an indication. If the device was in
continuous streaming mode, the UHD software will automatically restart
streaming when the buffer has space again.

\subsection general_ounotes_underrun Underrun notes

When transmitting, the device consumes samples at a constant rate.
Underflow occurs when the host does not produce data fast enough. When
UHD software detects the underflow, it prints a "U" to stdout, and
pushes a message packet into the async message stream.

<b>Note:</b> "O" and "U" message are generally harmless, and just mean the host machine can't keep up with the requested rates.

\section general_threading Threading Notes

\subsection general_threading_safety Thread safety notes

For the most part, UHD software is thread-safe. Please observe the
following limitations:

<b>Fast-path thread requirements:</b> There are three fast-path methods for
a device: `send()`, `recv()`, and `recv_async_msg()`. All three
methods are thread-safe and can be called from different thread
contexts. For performance, the user should call each method from a
separate thread context. These methods can also be used in a
non-blocking fashion by using a timeout of zero.

<b>Slow-path thread requirements:</b> It is safe to change multiple
settings simultaneously. However, this could leave the settings for a
device in an uncertain state. This is because changing one setting could
have an impact on how a call affects other settings. Example: setting
the channel mapping affects how the antennas are set. It is recommended
to use at most one thread context for manipulating device settings.

\subsection general_threading_prio Thread priority scheduling

When UHD software spawns a new thread, it may try to boost the thread's
scheduling priority. If setting the new priority fails, the UHD software
prints a warning to the console, as shown below. This warning is harmless;
it simply means that the thread will retain a normal or default scheduling priority.

    UHD Warning:
        Unable to set the thread priority. Performance may be negatively affected.
        Please see the general application notes in the manual for instructions.
        EnvironmentError: OSError: error in pthread_setschedparam

<b>Linux Notes:</b>

Non-privileged users need special permission to change the scheduling
priority. Add the following line to the file `/etc/security/limits.conf`:

    @GROUP    - rtprio    99

Replace `GROUP` with a group in which your user is a member. You may need
to log out and log back into the account for the settings to take effect.
In most Linux distributions, a list of groups and group members can be found in the file `/etc/group`.

\section general_misc Miscellaneous Notes

\subsection general_misc_dynamic Support for dynamically loadable modules

For a module to be loaded at runtime, it must be:

- found in the `UHD_MODULE_PATH` environment variable,
- installed into the `\<install-path\>/share/uhd/modules` directory,
- or installed into `/usr/share/uhd/modules` directory (UNIX only).

\subsection general_misc_prints Disabling or redirecting prints to stdout

The user can disable the UHD library from printing directly to stdout by
registering a custom message handler. The handler will intercept all
messages, which can be dropped or redirected. Only one handler can be
registered at a time. Make **register_handler** your first call into
the UHD library:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~{.cpp}
#include <uhd/utils/msg.hpp>

void my_handler(uhd::msg::type_t type, const std::string &msg){
//handle the message...
}

uhd::msg::register_handler(&my_handler);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

*/
// vim:ft=doxygen: